Local exhaust ventilation shall consist of movable hoods positioned close to the work and shall be of such capacity and arrangement as to keep breathing zone concentrations below hazardous levels. When practical, objects to be welded, cut, or heated shall be moved to a designated safe location or, if the objects to be welded, cut, or heated cannot be readily moved, all movable fire hazards in the vicinity shall be taken to a safe place, or otherwise protected. Occupational Safety & Health Administration, Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers, Severe Storm and Flood Recovery Assistance. Input power terminals, top change devices and live metal parts connected to imput circuits shall be enclosed and accessible only by means of insulated tools. 1926.1002 - Protective frames (roll-over protective structures, known as ROPS) for wheel-type agricultural and industrial tractors used in construction. 1926.1405 - Disassemblyadditional requirements for dismantling of booms and jibs (applies to both the use of manufacturer procedures and employer procedures). .
Ventilation and employee protection in welding, cutting and heating -. 1926.652 - Requirements for protective systems. 1926 Subpart Q App A - References to Subpart Q of Part 1926. 1926.962 - Grounding for the protection of employees. (1378.96 kPa) before reuse. INTRODUCTION . Structures or pipelines acting continuously as ground return circuits shall have joints bonded and maintained to ensure that no electrolysis or fire hazard exists. Welding Hazards burns & fire impact penetration The Division of Occupational Safety and Health (DOSH), better known as Cal/OSHA, protects and improves the health and safety of working men and women in California and the safety of passengers riding on elevators, amusement rides, and tramways - through the following activities: Setting and enforcing standards 0000013825 00000 n
When the welding, cutting, or heating operation is such that normal fire prevention precautions are not sufficient, additional personnel shall be assigned to guard against fire while the actual welding, cutting, or heating operation is being performed, and for a sufficient period of time after completion of the work to ensure that no possibility of fire exists. 29 CFR 1910.146 Permit Required - Confined Spaces; 29 CFR 1926.1206 Confined Spaces in Construction Variations of one or two shade numbers are permissible to suit individual preferences. 1926.50 App A - Medical services and first aid. 0000066083 00000 n
Some of the rules apply to dangerous jobs like hot worksuch as welding and cuttingrequired for activities as diverse as bio-pharmacy, food production, nuclear power generation, and aviation. Appropriate precaution shall be taken to prevent ignition of highly flammable hardened preservative coatings. When openings or cracks in flooring cannot be closed, precautions shall be taken to ensure that no employees or flammable or combustible materials on the floor below are exposed to sparks dropping through the floor. 1926.20 - General safety and health provisions. 1926.651 - Specific Excavation Requirements. 1926.914 - Definitions applicable to this subpart. Unless cylinders are firmly secured on a special carrier intended for this purpose, regulators shall be removed and valve protection caps put in place before cylinders are moved. 1926.1153 - Respirable crystalline silica. In flammable or potentially flammable atmospheres: On or in equipment or tanks that have contained flammable gas or liquid or combustible liquid or dust-producing material, until a designated person has tested the atmosphere inside the equipment or tanks and determined that it is not hazardous; or. Nomenclature changes to part 1926 appear at 84 FR 21597, May 14, 2019. 1926.1441 - Equipment with a rated hoisting/ lifting capacity of 2,000 pounds or less. Any precautions that the host employer or any previous controlling contractor or entry employer implemented for the protection of employees in the permit space. osha hot work permit requirements 1926; hot work permit checklist; hot work hazards and control measures pdf; sample hot work permit for cutting or welding; How to Edit Your Hot Work Permit Osha Standard Online. The control apparatus of arc welding machines shall be enclosed, except for operating wheels, levers, and handles. 1926.853 - Removal of materials through floor openings. 1926.441 - Batteries and battery charging. The person cracking the valve shall stand to one side of the outlet, not in front of it. Similar precautions shall be taken regarding cracks or holes in walls, open doorways and open or broken windows. Shall have valve protection caps in place except when in use, hooked up or secured for movement. 0000019967 00000 n
If the object to be welded or cut cannot readily be moved, all movable fire hazards in the vicinity shall be taken to a safe place. When hot work must be performed in a location that is not free of fire hazards, all necessary precautions shall be taken to confine heat, sparks, and slag so that they cannot contact flammable or combustible material. 0000054473 00000 n
1926.1403 - Assembly/Disassemblyselection of manufacturer or employer procedures. When parallel sections of oxygen and fuel gas hose are taped together, not more than 4 inches out of 12 inches shall be covered by tape. They shall not be intentionally dropped, struck, or permitted to strike each other violently. 1926.95 - Criteria for personal protective equipment. The results of tests and monitoring performed under 1926.1204(e), accompanied by the names or initials of the testers and by an indication of when the tests were performed; The rescue and emergency services that can be summoned and the means (such as the equipment to use and the numbers to call) for summoning those services; The communication procedures used by authorized entrants and attendants to maintain contact during the entry; Equipment, such as personal protective equipment, testing equipment, communications equipment, alarm systems, and rescue equipment, to be provided for compliance with this standard; Any other information necessary, given the circumstances of the particular confined space, to ensure employee safety; and. When arc welding is performed in wet or high-humidity conditions, employees shall use additional protection, such as rubber pads or boots, against electric shock. They shall not be hoisted or transported by means of magnets or choker slings. Fuel gas and oxygen hoses shall be easily distinguishable from each other by color or sense of touch. 67 0 obj
<>
endobj
xref
A copy of the contractor's written Hot Work Permit Procedures shall be available for EH&S review. Employees exposed to radiation shall have their skin covered completely to prevent ultraviolet burns and damage. Hot work areas shall not be less than 35 feet from combustible materials and combustible waste 1910.252 (a) (1) (ii) Guards. 1926.1153 App A - Methods of Sample Analysis, 1926.1153 App B - Medical Surveillance Guidelines, 1926 Subpart AA - Confined Spaces in Construction. 1926.64 - Process safety management of highly hazardous chemicals. A hot work permit is a legal document that is required in certain situations where work is being performed that may generate heat, sparks, or flames. The atmosphere within the space must be continuously monitored unless the entry employer can demonstrate that equipment for continuous monitoring is not commercially available or periodic monitoring is sufficient. Pressure regulators. No hazardous atmosphere is permitted within the space whenever any employee is inside the space. Fuel gas shall be used only as follows: Before regulators are connected to cylinder valves, the valves shall be opened slightly (cracked) and closed immediately to clear away dust or dirt. Torches shall be inspected before each use for leaking shut-off valves, hose couplings and tip connections. 1926.705 - Requirements for lift-slab construction operations. Defective hose shall not be used. 0000052163 00000 n
1926.1103 - 13 Carcinogens (4-Nitrobiphenyl, etc.). 0000036037 00000 n
1926.200 - Accident prevention signs and tags. Fires are often the result of the "quick five minute" job in areas not intended for welding or cutting. California State University - San Marcos (CSUSM) is dedicated to the protection of our 0000012747 00000 n
1926.1433 - Design, construction and testing. Note to paragraph (d). Oxygen cylinders in storage shall be separated from fuel-gas cylinders or combustible materials (especially oil or grease), a minimum distance of 20 feet (6.1 m) or by a noncombustible barrier at least 5 feet (1.5 m) high having a fire-resistance rating of at least one-half hour. 1926.804 - Definitions applicable to this subpart. A Hot Work Permit is required whenever any hot work activity is conducted outside of an area designated for hot work. 1926 Subpart L App D - List of Training Topics for Scaffold Erectors and Dismantlers. 1926.904 - Storage of explosives and blasting agents. They shall not be hoisted or transported by means of magnets or choker slings. 1926.1437 - Floating cranes/derricks and land cranes/derricks on barges. Permit space entry is performed at the same time that any activities that could foreseeably result in a hazard in the permit space are performed. 1926.1205 (c) 1926.405 - Wiring methods, components, and equipment for general use. Permits usu-ally are valid only for the length of the working shift; but never more than 24 hours. 1926.961 - Deenergizing lines and equipment for employee protection. 6, 1979, as amended at 55 FR 42328, Oct. 18, 1990; 58 FR 35179, June 30, 1993], Occupational Safety & Health Administration. A hot work permit is a legal requirement in certain areas or job sites that gives workers or contractors the authorization to proceed with hot work activities. 1926 Subpart CC - Cranes and Derricks in Construction. Occupational Safety & Health Administration. 0000003523 00000 n
1926.352 (b) 0000009131 00000 n
The OSHA 300 Log must be maintained by employers unless there is an exemption, based on the NAICS code or the size of . Oregon OSHA provides a variety of publications, including; guide books, brochures, forms, hazard alerts, fact sheets, posters, cards, stickers, reports, and checklists on a variety of workplace health and safety topics. 1926.14 - Federal contract for "mixed" types of performance. When this is impractical, fire resistant shields shall be provided. Where required by your AHJ, use this fillable PDF form to complete and submit your AHJ Hot Work Permit application electronically - saves time printing and scanning! }m?"Qwk&Ubm5"W`K`!xC_[2Vk"e,X,bYGv`[=. The California Code of Regulations (CCR), title 8, section 341 and section 341.1 require employers to obtain Project Permits and Annual Permits from Cal/OSHA before conducting certain construction activities. The tips below can help you fill out Osha Hot Work Permit Form Pdf easily and quickly: Open the template in the full-fledged online editor by hitting Get form. 1926.700 - Scope, application, and definitions applicable to this subpart. Drums, containers or hollow structures that have contained flammable or combustible substances shall either be filled with water or cleaned, and shall then be ventilated. 1926 Subpart G - Signs, Signals, and Barricades. This section contains the required practices and procedures necessary to protect employees from fire and explosion hazards associated with hot work. Standard for Fire Prevention During Welding, Cutting, and Other Hot Work This standard presents provisions to prevent injury, loss of life, and loss of property from fire or explosion as a result of hot work projects such as welding, heat treating, grinding, and similar applications producing or using sparks, flames, or heat. Drums containers, or hollow structures which have contained toxic or flammable substances shall, before welding, cutting, or heating is undertaken on them, either be filled with water or thoroughly cleaned of such substances and ventilated and tested. 1926.704 - Requirements for precast concrete. 1926.65 - Hazardous waste operations and emergency response. 1926 Subpart R App F - Perimeter Columns: Non-Mandatory Guidelines for Complying with 1926.756(e) To Protect the Unprotected Side or Edge of a Walking/Working Surface. Hot work means any activity in which flame, heat, or spark is generated. HOT WORK SAFETY GUIDE . Inform the controlling contractor of the permit space program that the entry employer will follow, including any hazards likely to be confronted or created in each permit space. Hot work includes cutting, welding, brazing, soldering, and any process involving the application of a naked flame. Each employee must leave the space immediately; The space must be evaluated to determine how the hazard developed; and. 1926.956 - Hand and portable power equipment. The controlling contractor must debrief each entity that entered a permit space regarding the permit space program followed and any hazards confronted or created in the permit space(s) during entry operations; The entry employer must inform the controlling contractor in a timely manner of the permit space program followed and of any hazards confronted or created in the permit space(s) during entry operations; and. 0000016958 00000 n
When welding, cutting, or heating is performed on walls, floors, and ceilings, since direct penetration of sparks or heat transfer may introduce a fire hazard to an adjacent area, the same precautions shall be taken on the opposite side as are taken on the side on which the welding is being performed. Provide the following information to each entity entering a permit space and any other entity at the worksite whose activities could foreseeably result in a hazard in the permit space: The information received from the host employer; Any additional information the controlling contractor has about the subjects listed in paragraph (h)(1) of this section; and. Hose couplings shall not unlock or disconnect without rotary motion. When cylinders are hoisted, they shall be secured on a cradle, slingboard, or pallet. In accordance with OSHA standards, contractors are required to apply for these permits through the company's permit-authorizing individual (PAI). Note to paragraph (h). The employer shall ensure that when arc welders or cutters leave or stop work or when machines are moved, the power supply switch shall be kept in the off position. sb`aY Yann Wehrling, vice-prsident de la rgion le-de-France, charg de la Transition cologique, et Patrice Leclerc, maire de Gennevilliers et Prsident du groupe Front De Gauche la . 1926.406 - Specific purpose equipment and installations. 1926.11 - Coverage under section 103 of the act distinguished. 1926 Subpart R App A - Guidelines for establishing the components of a site-specific erection plan: Non-Mandatory Guidelines for Complying with 1926.752(e). Any employee who enters the space, or that employee's authorized representative, must be provided with an opportunity to observe the testing required by this paragraph (e)(2)(vi). 1926.251 - Rigging equipment for material handling. 1926.951 - Medical services and first aid. 1926.752 - Site layout, site-specific erection plan and construction sequence. A single hose having more than one gas passage shall not be used. An uncoiled fire hose with fog nozzle, under pressure, shall be immediately available in the hot work area. Yes, permits for performing hot work are required by both OSHA and the National Fire Protection Association (NFPA), in addition to the local fire code. %PDF-1.7
%
Table G-1 - Filter Lenses for Protection Against Radiant Energy. Surfaces covered with preservative coatings shall be stripped for at least 4 inches (10.16 cm) from the area of heat application or employees shall be protected by supplied air respirators in accordance with the requirements of 1910.134 of this chapter. 1926 Subpart R App E - Training: Non-mandatory Guidelines for Complying with 1926.761. The review identifies the type and location of the work, personnel roles, and responsibilities, necessary precautions, and duration of the permit. The entry permit that documents compliance with this section and authorizes entry to a permit space must identify: The date and the authorized duration of the entry permit; The authorized entrants within the permit space, by name or by such other means (for example, through the use of rosters or tracking systems) as will enable the attendant to determine quickly and accurately, for the duration of the permit, which authorized entrants are inside the permit space;
Warm, not boiling, water shall be used to thaw cylinders loose. Highly flammable coatings shall be stripped from the area to be heated. The in-plant handling, storage, and utilization of all compressed gases in cylinders, portable tanks, rail tankcars, or motor vehicle cargo tanks shall be in accordance with Compressed Gas Association Pamphlet P-1-1965. Before it begins work at a worksite, each employer must ensure that a competent person identifies all confined spaces in which one or more of the employees it directs may work, and identifies each space that is a permit space, through consideration and evaluation of the elements of that space, including testing as necessary. 1926.1102 - Coal tar pitch volatiles; interpretation of term. 1926.906 - Initiation of explosive charges-electric blasting. Oil and grease hazards. 1926 Subpart Y App A - Examples of Conditions Which May Restrict or Limit Exposure to Hyperbaric Conditions, 1926 Subpart Y App B - Guidelines for Scientific Diving, 1926 Subpart Z - Toxic and Hazardous Substances, 1926.1101 App A - OSHA Reference Method - Mandatory, 1926.1101 App B - Sampling and Analysis - Non-mandatory, 1926.1101 App C - Qualitative and quantitative fit testing procedures - Mandatory, 1926.1101 App D - Medical Questionnaires; Mandatory, 1926.1101 App E - Classification of Chest X-Rays - Mandatory, 1926.1101 App F - Work practices and engineering controls for Class I Asbestos Operations - non-mandatory, 1926.1101 App H - Substance Technical Information for Asbestos - Non-Mandatory, 1926.1101 App I - Medical Surveillance Guidelines for Asbestos, Non-Mandatory, 1926.1101 App J - Smoking cessation program information for asbestos, non-mandatory, 1926.1101 App K - Polarized Light Microscopy of Asbestos - Non-Mandatory. The employer must verify that the space is safe for entry and that the preentry measures required by paragraph (e)(2) of this section have been taken, through a written certification that contains the date, the location of the space, and the signature of the person providing the certification. Lou, Paris 11eme, recherche des personnes motives et comptentes qui partagent notre enthousiasme pour la gastronomie, le vin et l'hospitalit pour devenir Chef de Parties dans notre quipe . 1926.1406 - Assembly/Disassemblyemployer procedures--general requirements. 0000002304 00000 n
Adapters shall not be used to permit the interchange of hose. 0000065715 00000 n
the required city permits, when necessary, for such work. 0000046103 00000 n
Near any area in which exposed readily ignitable materials such as bulk sulphur, baled paper or cotton are stored. 1926.1204 - Permit-required confined space program. Oxygen and fuel hoses shall not be interchangeable. 0000035922 00000 n
1926.905 - Loading of explosives or blasting agents. No one except the owner of the cylinder or person authorized by him, shall refill a cylinder. Inform exposed employees by posting danger signs or by any other equally effective means, of the existence and location of, and the danger posed by, each permit space; and
Suitable fire extinguishing equipment shall be immediately available in the work area and shall be maintained in a state of readiness for instant use. 1917.152 - Welding, cutting and heating (hot work)[12] (See also 1917.2, definition of Hazardous cargo, materials, substance, or atmosphere). The certification must be made available to each employee entering the space or to that employee's authorized representative; and. Use the e-signature solution to e-sign the form. The controlling contractor and entry employer(s) must coordinate entry operations when: More than one entity performs permit space entry at the same time; or. Welding & cutting operations, conducted outside authorized hot work areas, includes extensive procedures for fire prevention. Hot Work Safety Guide 06/2015 1 . 1926 Subpart V - Electric Power Transmission and Distribution. 1926.449 - Definitions applicable to this subpart. 1926.1127 App A - Substance Safety Data Sheet - Cadmium, 1926.1127 App B - Substance Technical Guidelines for Cadmium, 1926.1127 App C - Qualitative and Quantitative Fit Testing Procedures, 1926.1127 App D - Occupational Health History Interview With Reference to Cadmium Exposure, 1926.1127 App E - Cadmium in Workplace Atmospheres, 1926.1127 App F - Nonmandatory Protocol for Biological Monitoring. hot work hazards and control measures pdf. 0000002269 00000 n
An OSHA "permit" is an employer-created and signed document that details the safeguards in place to protect an employee who's been assigned a particularly dangerous job function like working in a confined space, welding and cutting, or working on "live" electrical equipment. If testing and inspection during that entry demonstrate that the hazards within the permit space have been eliminated or isolated, the permit space may be reclassified as a non-permit confined space for as long as the hazards remain eliminated or isolated; The entry employer must document the basis for determining that all hazards in a permit space have been eliminated or isolated, through a certification that contains the date, the location of the space, and the signature of the person making the determination. How and when to acquire a hot work permit and who can supervise them. Fill in the necessary boxes that are colored in yellow. If the leak continues, the cylinder shall be tagged, removed from service, and moved to a location where the leak will not be hazardous. Grounding circuits shall have resistance low enough to permit sufficient current to flow to cause the fuse or circuit breaker to interrupt the current. Hose connections shall be clamped or securely fastened to withstand twice the normal working pressure but not less than 300 p.s.i. Ask how long hot work permits are valid. 1926.703 - Requirements for cast-in-place Concrete. 1926.1003 - Overhead protection for operators of agricultural and industrial tractors used in construction. Pressure-reducing regulators shall be attached to cylinder valves when cylinders are supplying torches or devices equipped with shut-off valves; Cylinder valves shall be closed and gas released from the regulator or manifold before regulators are removed; Leaking fuel gas cylinder valves shall be closed and the gland nut tightened. When the hot work operation is such that normal fire prevention precautions are not sufficient, additional personnel shall be assigned to guard against fire during hot work and for a sufficient time after completion of the work to ensure that no fire hazard remains. 1926 Subpart L App A - Scaffold Specifications, 1926 Subpart L App B - Criteria for Determining the Feasibility of Providing Safe Access and Fall Protection for Scaffold Erectors and Dismantlers. All cylinders used shall meet the Department of Transportation requirements published in 49 CFR part 178, subpart C, Specification for Cylinders. Assigned storage places shall be located where cylinders will not be knocked over or damaged by passing or falling objects, or subject to tampering by unauthorized persons. For Compliance With . 1926.2 - Variances from safety and health standards. 1926.500 - Scope, application, and definitions applicable to this subpart. If hazards arise within a permit space that has been reclassified as a non-permit space under paragraph (g) of this section, each employee in the space must exit the space. F. FIRE SAFETY REQUIREMENTS (As per Section 2604 of FDNY Fire Code) Separation from combustibles. The permit shall document that the fire prevention and protection requirements in 29 CFR 1910.252 (a) have been implemented prior to beginning the hot work operations, indicate the date (s) authorized for hot work, and identify the object on which hot work is to be performed (68.85). Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers, Severe Storm and Flood Recovery Assistance. 0000014709 00000 n
1926 Subpart H - Materials Handling, Storage, Use, and Disposal. 0000015110 00000 n
Means of detecting an increase in atmospheric hazard levels in the event the ventilation system stops working; Each person, by name, currently serving as an attendant; The individual, by name, currently serving as entry supervisor, and the signature or initials of each entry supervisor who authorizes entry; The hazards of the permit space to be entered; The measures used to isolate the permit space and to eliminate or control permit space hazards before entry;
The employer must ensure a safe method of entering and exiting the space. 0000020449 00000 n
Hot electrode holders shall not be dipped in water. Where relocation is impractical, combustibles shall be protected with flame proof covers, shielded with metal, guards, curtains, or wet down material to help prevent ignition of . Fuel gas shall not be used from cylinders through torches or other devices which are equipped with shutoff valves without reducing the pressure through a suitable regulator attached to the cylinder valve or manifold. Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers, Severe Storm and Flood Recovery Assistance, Inert-gas Metal-Arc Welding (Non-ferrous) 1/16- to 5/32-inch electrodes. The employer must implement measures to protect employees from the hazard before any subsequent entry takes place. Inside of buildings, cylinders shall be stored in a well-protected, well-ventilated, dry location, at least 20 feet (6.1 m) from highly combustible materials such as oil or excelsior. osha hot work permit requirements 1926. hot work procedure. Use of fuel gas. 1926.97 - Electrical protective equipment. The written program must be made available prior to and during entry operations for inspection by employees and their authorized representatives. Occupational Safety & Health Administration, Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers. OSHA 300 Log of Work-Related Fatalities, Injuries and Illness. Entry into the permit space under the terms of paragraph (e)(1) of this section is performed in accordance with the requirements of paragraph (e)(2) of this section. For the elimination of possible fire in enclosed spaces as a result of gas escaping through leaking or improperly closed torch valves, the gas supply to the torch shall be positively shut off at some point outside the enclosed space whenever the torch is not to be used or whenever the torch is left unattended for a substantial period of time, such as during the lunch period. 1926.1407 - Power line safety (up to 350 kV)assembly and disassembly. 14 of 1950. 1926 Subpart L App C - List of National Consensus Standards. Before hot work is commenced on surfaces covered by a preservative coating of unknown flammability, a test shall be made by a designated person to determine the coating's flammability.
1926.858 - Removal of steel construction. A sign reading "DANGER-PERMIT-REQUIRED CONFINED SPACE, DO NOT ENTER" or using other similar language would satisfy the requirement for a sign. 1926 Subpart R App D - Illustration of the Use of Control Lines To Demarcate Controlled Decking Zones (CDZs): Non-mandatory Guidelines for Complying With 1926.760(c)(3). Oxygen and fuel gas pressure regulators, including their related gauges, shall be in proper working order while in use. 1926.1050 - Scope, application, and definitions applicable to this subpart. This Safe Work Permits eBook will cover important details of the following federal regulations, including definitions, key requirements, and exemptions (if any) to ensure safety compliance in the workplace. Mechanical ventilation requirements. Nothing shall be placed on top of a manifold, when in use, which will damage the manifold or interfere with the quick closing of the valves. Surfaces prepared with chlorinated solvents shall be thoroughly dry before welding is performed on them. If a leak should develop at a fuse plug or other safety device, the cylinder shall be removed from the work area. Hoses, cables, and other equipment shall be kept clear of passageways, ladders and stairs. H\n0z 1926.955 - Portable ladders and platforms. Insert the date. 0000006757 00000 n
0000009657 00000 n
Ground return cables shall have current-carrying capacity equal to or exceeding the total maximum output capacities of the welding or cutting units served.